ISO 9001
REGISTERED FIRM

WEDGE & CHAMBER CONSTRUCTION

Attenuating Structures In order to obtain a suitable sound environment, the anechoic chamber lining is installed in a proper noise isolating structure. This enclosure may be one of several types of construction built on an isolated floor, or floated on springs or other vibration isolation material.

Masonry A masonry enclosure is typically used in new construction, or when the anechoic facility is planned as an integral part of a new building. A 200mm or 300mm (8" or 12") masonry block usually provides adequate noise reduction. The addition of an inner panel room will provide increased noise reduction when required. Walls should be constructed on an isolated reinforced floor separated from the building floor or in a pit to allow the working floor in a chamber to be flush with the host room floor.
Panelled Rooms Eckel provides enclosures built from Eckoustic panels with solid faces on both sides. Eckoustic panel rooms are completely pre-fabricated in the factory and can be quickly erected in an existing facility. These modular enclosures allow for flexible arrangements of doors and utilities. Doors are structurally and acoustically compatible with the wall construction. Hard spots or internal framing are provided for attachment of hardware. Penetrations for lights, power, instrumentation wiring, and ventilation are incorporated into the panel construction.
Working Floors (Cable or Grating) Since Anechoic Chamber Wedges are not designed to support heavy loads, a working floor must be provided over the top of the floor wedge points. Eckel recommends two types for general use: spring tension cable floors and grating floors (expanded and subway grating). Spring tensioned cable floors are best from an acoustical standpoint, whereas floor gratings are desirable where concentrated loads must be supported. Floor gratings are provided in sections so they can be removed during testing.
Entrance Doors The Anechoic Chamber entrance sound attenuating doors can be fabricated in a variety of designs, including swing-in or swing-out hinged type, sliding-wall type, or track-riding type. Also offered is the space-saving interlocking wedge door. Here, Anechoic wedges are mounted directly onto the door. When the door is swung open into the chamber, the wedge points interlock with those on the adjacent wall, minimizing the amount of lost space in the chamber

Ventilation Design

The ventilation system in the Eckel anechoic chamber is designed to maintain a uniform temperature, provide fresh air for humans and/or animals and facilitate proper combustion in air-consuming equipment. Ten to twelve air changes per hour of the free field volume will generally maintain uniform temperature and provide ample fresh air for humans or animals, while removing normal heat from lights, body radiation, and instrumentation.

Installation Procedure

Eckel anechoic linings are constructed according to a strictly supervised installation protocol. chamber linings are installed on roll formed wedge tracks attached to wall and ceiling surfaces by means of a "Z" bar mounting system. As wedges are erected, the space between the wedges is filled with light density compressible fiberglass or melamine foam.

Instrumentation Hangers

Eckel installs all hangers and brackets required to support instrumentation and test specimens. This includes a network of all necessary cables or wires. Eckel provides engineering or design data pertinent to the support of any type of equipment within an anechoic chamber upon request to the purchasers, and their consultants or engineers.

Penetration Sleeves

Electrical power, wiring, and other services are introduced into the anechoic chamber by pipe sleeves that pass through the basic structure and wedges. Eckel Industries plans pipe penetrations carefully so that they enter the chamber through the valleys of the wedges and not the joints between the wedges.

Lighting, Electrical

Electric services are always installed in compliance with local or UL-approved regulations. Electric light, conduits, and outlets usually penetrate the structure through the wedge valleys and terminate at that point with the appropriate outlet or fixture.

Vibration Isolation

Anechoic Chambers shall be isolated from structural vibration by one of the following systems.

Reverberation Rooms

Eckel Reverberation rooms are designed for the determination of sound output of noise sources, transmission loss of partitions, insertion loss of silencers, response characteristics of microphones, and random incidence absorption coefficients of materials. Eckel reverberation rooms satisfy reverberant test requirements and meet specific interior sound levels and other environmental requirements necessary for proper test measurements.

Other Available Features

Eckel offers RF shielding, temperature and humidity control and other special features depending on client needs. Fiberglass cloth cover option protects against fiber migration, especially where the chamber will be incorporated into a wind tunnel test configuration.

For more information, fill out an Eckel Anechoic Chamber Check List